Twist TrueAmp Library Preparation Kit

Yes, fragmented and end-prepped DNA can be safely stored at either 4 °C or -20 °C (e.g., overnight) prior to ligation without any appreciable impact on library preparation performance as compared to samples processed immediately. This has been validated across technical replicates (n=3), where samples were stored under these conditions before ligation and showed consistent results.

Yes. The TrueAmp reagents have been tested through up to four freeze-thaw cycles with no observed impact on performance. These studies were conducted over multiple days to reflect typical laboratory use. As a best practice, repeated freeze–thaw cycles should still be minimized when possible.

Yes, contaminants such as salts, EDTA, ethanol, detergents, and extraction reagent carryover can impact enzymatic fragmentation. These may either inhibit or enhance enzyme activity, leading to inconsistent or shifted fragment sizes.

In some cases, fragmentation can be tuned by adjusting incubation time or temperature to compensate. However, if inhibitors significantly disrupt enzyme activity and no library is generated, we recommend performing an additional DNA cleanup before library preparation.

Yes, the TrueAmp Library Preparation Kit performs well with degraded and FFPE-derived DNA. The workflow includes DNA repair activity, which can help restore damaged bases commonly found in FFPE samples.

As a result, users often observe improved library yield and recovery compared to workflows without repair. Some optimization (e.g., fragmentation time, PCR cycles) may be required depending on sample quality.

Yes. The TrueAmp fragmentation chemistry is broadly compatible with a range of double-stranded DNA inputs, including genomic DNA (gDNA), plasmids, and PCR-derived amplicons. Under consistent reaction conditions, high-quality DNA substrates, regardless of origin, typically yield comparable fragment size distributions, indicating minimal sequence or topology-dependent bias.

During development, fragmentation performance was evaluated using DNA ladders spanning a wide range of fragment sizes. This study demonstrates that the enzymatic fragmentation preferentially processes larger DNA molecules while maintaining representation of shorter fragments, resulting in a controlled size distribution without significant loss of diversity across the input population.

No, the TrueAmp Library Preparation Kit is not compatible with bisulfite conversion or EM-seq workflows. The enzymatic steps in the TrueAmp Library Preparation workflow include DNA repair, which can alter or remove native methylation signatures.

For methylation-sensitive applications such as bisulfite or EM-seq, we recommend using mechanical shearing (e.g., sonication) followed by the Twist cfDNA Library Preparation Kit, which is better suited for preserving methylation information.

The TrueAmp Library Preparation Kit is not recommended for cfDNA workflows. Since cfDNA is already fragmented, the enzymatic fragmentation step is unnecessary. While it is possible to skip fragmentation and proceed with end repair and dA-tailing, the one-pot workflow may not deliver optimal conversion efficiency for these short fragments.

For best performance and highest library conversion from cfDNA, we recommend using the Twist cfDNA Library Preparation Kit, which is specifically optimized for cell-free DNA.

Yes, the TrueAmp Library Preparation Kit is well suited for targeted enrichment workflows, including hybrid capture applications. It generates high library yields and promotes uniform molecule conversion, which supports efficient and consistent downstream target capture performance.

Yes, the TrueAmp Library Preparation Kit is compatible with liquid handling automation platforms such as Hamilton systems. The streamlined workflow, reduced number of steps, and minimal hands-on time make it well suited for automation. Minor optimization (e.g., mixing, bead handling, or liquid classes) may be required depending on the platform and configuration.

No. The enzymatic fragmentation chemistry is designed to produce consistent fragment sizes across the recommended input range, so fragmentation time and temperature do not need to be adjusted based on DNA mass.

Under the same conditions, samples with similar DNA quality ranging from 0.1 ng to 500 ng will generate comparable fragment size distributions. Demonstrated above, human genomic DNA inputs from 0.1 ng to 500 ng fragmented at 32°C for 22 minutes produced similar final library sizes (~450–480 bp), with PCR cycle number increasing as input mass decreased

Fragment size can be controlled by adjusting fragmentation reaction temperature and incubation time. Increasing either parameter generally results in shorter DNA fragments, while reducing them produces longer fragments.

Because fragmentation performance can vary depending on thermocycler calibration, DNA input quality, and storage buffer composition, we recommend performing a small design of experiments (DOE) with your specific samples to determine optimal conditions prior to scaling up.

For additional guidance and example data, please refer to the Twist TrueAmp Library Preparation Kit technical note on insert size optimization.

Adapter input should be adjusted based on DNA input amount and fragment size to maintain sufficient adapter-to-insert molar excess for efficient ligation while minimizing adapter-dimer formation. Twist Universal Adapters are supplied at 10 µM and recommended conditions in the protocol are designed to maintain an adapter-to-insert molar ratio of approximately ≥150:1 for robust ligation efficiency across a broad range of inputs. Too little adapter may reduce library conversion and yield, while excessive adapter can increase adapter-dimer carryover, particularly in low-input samples.

If optimization is required, titrate adapter input while monitoring final library yield and adapter-dimer levels. The optimal condition is the lowest adapter amount that maintains strong library yield with minimal adapter dimer.

For ultra-low input samples (<1 ng), additional optimization may be required to balance ligation efficiency against adapter-dimer formation, as reduced insert mass increases the likelihood of adapter self-ligation products. Conversely, for higher DNA input amounts, increasing adapter concentration beyond the recommended range may further improve ligation efficiency in some workflows.

Input DNA quality directly affects fragment size. High-quality, intact DNA produces predictable insert sizes, while degraded or pre-sheared DNA (e.g., FFPE) typically results in shorter fragments under the same conditions. In these cases, reducing fragmentation time or temperature and applying size selection may help achieve the desired insert size.

Yes. Vortexing the 10X Twist Fragmentation Enzyme Mix prior to use is important to ensure the solution is fully homogeneous. Failure to properly mix the enzyme solution may lead to variability in fragmentation performance and inconsistent results.

The TrueAmp Library Preparation Kit is designed for flexibility and is compatible with a wide range of 3′ T-overhang adapters. Note that adapter quality impacts overall library preparation efficiency. For optimal performance, we recommend using validated Twist adapter systems:

●        Twist Universal Adapter System (SKU: 101308)

○    Requires PCR amplification with indexed primers to complete library construction.

●        Twist UMI Adapter System (SKU: 105041)

○        Requires PCR amplification with indexed primers.

○        Enables incorporation of Unique Molecular Identifiers (UMIs) for improved error correction and duplicate handling.

●        Twist Full-Length UDI Adapters (SKU: 107376)

○        Do not require PCR for index incorporation, as full-length P5/P7 sequences and indices are already present.

○        Optional PCR may still be performed for library amplification if additional yield is needed.

All three systems are fully compatible with the TrueAmp workflow. Selection should be based on your application needs (e.g., UMI requirements, workflow, or PCR-free indexing preference).

The TrueAmp Library Prepration Kit supports a broad range of DNA input amounts, from as low as 100 pg up to 1 µg. This flexibility enables reliable library preparation across low-input and high-input sample types.

The TrueAmp Library Preparation Kit has a shelf life of 12 months when stored as recommended. This is supported by accelerated aging studies conducted over 13 months, which showed no measurable impact on performance or stability.

Three independent manufacturing lots were evaluated to assess fragmentation variability, with an additional operator performing replicate testing on a separate day to characterize operator-to-operator effects.

Fragmentation with the TrueAmp Library Preparation Kit demonstrates high reproducibility within a given lot, with technical replicates (n=8) showing tight fragment size distributions and a standard deviation of ~7–10 bp (~2% CV). Across manufacturing lots, modest shifts in the mean fragment size are observed (~30–40 bp, or ~5–8% deviation), while maintaining consistent distribution shape and overall library performance. Operator-to-operator variability can introduce similar shifts in the average fragment size, as observed within the same lot; however, these differences should not meaningfully impact the distribution profile or downstream performance. 

The TrueAmp Library Preparation Kit is designed for flexible DNA library construction across a wide range of sample types and input amounts. It supports an integrated workflow where fragmentation, end repair, and dA-tailing are performed in a single enzyme mix, simplifying the overall process.

The kit performs robustly across diverse DNA inputs, including FFPE samples or samples with varying GC content and is compatible with DNA in common storage buffers such as TE, Tris-HCl, or water.

It also enables consistent and reliable fragmentation using a single standardized protocol, while also allowing users to tune insert size by adjusting incubation time or temperature. The streamlined workflow can be completed in approximately 3 hours, with less than 15 minutes of hands-on time, and is designed to maximize library yield through high reaction efficiency and minimal sample loss.